TANKCARE BT-01
1 PRODUCT DESCRIPTION
A two component, solvent free epoxy paint.
2 RECOMMENDED USE
As a non-solvent protective primer-finish coat can be used in freshwater tank, storage tank and water pipeline.Can be used as primer and fininsh coat in atmospheric and immersed environments.Suitable for properly prepared carbon steel, stainless steel and concrete substrates.
3 FEATURES
- Remarkable resistance to extensive range of solvents.
- High-build applicability.
- Excellent anti-abrasion and impact-resistant properties.
- Excellent Ultra thick film applicability.
4 COMPLIED STANDARDS
Complies with the standard GB 5369-2008 “General Technical Requirements for Coatings of Marine Drinking Water Tanks”
5 PHYSICAL PROPERTIES
| Item | Specification |
|---|---|
| Color | White |
| Gloss, GU@60° | No requirement |
| Mixing Ratio | Base/Hardener=20/5 |
| Specific gravity, g/cm³ | 1.32±0.1 |
| Volume Solids, % | 98±2% |
| Weight Solids, % | 98±2% |
| Film thickness | Dry ：100-200 microns/coat Wet：105-208microns/coat |
| Theoretical Coverage | 0.404 kg/m2/300microns Practical：Variable on surface conditions, environment, applications method, etc. |
6 APPLICATION
Application Temperature:
5℃-40℃
Application Condition:
The relative humidity of the air should not greater than 85%.
The substrate temperature is 3℃ higher than the dew point.
Pot life:
| Temperature (℃) | 10 | 20 | 30 |
|---|---|---|---|
| Pot life (mins) | 50 | 30 | 20 |
Application Methods:
Airless spray, Brush and roller
Airless spray
| Item | Specification |
|---|---|
| Nozzle tip size | 0.43mm ~ 0.68mm |
| Nozzle pressure | ≥25 Mpa |
| Thinning ratio |
Brush/Roller
| Item | Specification |
|---|---|
| Dilution ratio |
Thinner: Epoxy thinner (Only for Washing)
Drying time & Overcoating interval:
| Temperature | 10℃ | 20℃ | 30℃ |
|---|---|---|---|
| Dry to touch | 12hrs | 6hrs | 4hrs |
| Dry hard | 36hrs | 24hrs | 18hrs |
| Min interval | 36hrs | 24hrs | 18hrs |
| Max interval | 3days | 2days | 1days |
Applied substrate: Bare steel.
Coating system: TANKCARE BT-01
7 SURFACE PREPARATION
- Remove salt and other water-soluble contaminants by fresh water.
- Remove oil and grease with suitable detergent or solvent(SSPC-SP 1).
- Remove rust, mill-scale and other foreign materials completely by abrasive blasting to achieve ISO Sa2 1/2(SSPC-SP 10) or better.
- All coated surface must be clean, dry and free from any dust.
8 STORAGE
Storage
Shelf life
Store in dry, cool conditions, and away from sources of heat & ignition. Containers must be kept tightly closed.
12months/25℃
Shelf life：Subject to re-inspection thereafter.
9 CAUTIONS
CAUTIONS
SAFETY PRECAUTIONS
The following measures shall be ensured in all paint applications.
Avoid skin and eye contact.
If paint comes into contact with skin, wash with warm water and/or suitable cleanser. If paint comes into contact with the eyes, flush with copious amount of water and seek immediate medical attention.
Ensure good ventilation. Avoid inhalation of spray mist or vapour.
Application and handling of this product should be in compliance with relevant national regulations. Detail information is given on SDS.
DISCLAIMER
The information provided in this manual constitutes the most comprehensive and accurate data currently available to us. As the operating conditions of the product are beyond our control, this information does not constitute any warranty and is solely intended to assist the buyer in product selection. Given that our products and manufacturing processes are continuously evolving, this manual will be updated accordingly. All information herein shall be subject to our confirmation. Before using the product, please ensure that you have the latest version of this manual.
PREPARATION DATE
REVISION DATE
2025-03-12
2026-02-04.
